Close up photo of the end of the sling release cord indicating the position that is most critical to wax with Pan sling wax.
Close up photo of the end of the sling release cord indicating the position that is most critical to wax with Pan sling wax.

Pan's Sling Wax

$8
Los gastos de envío se calculan en la pantalla de pagos.
Size: 1 oz

Pan's Sling Wax is specifically designed with the extreme demands of slinging in mind. Made with a blend of waxes, including two types of beeswax, it does not contain paraffin. It is more flexible, and less likely to flake than paraffin-based fabric waxes. 

  • Abrasion protection (whip-crack fatigue) 
  • Add stiffness 
  • Wax edges of leather pouch
  • Increase grip of finger loop

See waxing instructions below.  

PAN's Sling Wax

Use Pan's Sling Wax on your cordage, leather edging, and finger loop.

Waxing your sling offers several advantages, including:

  • Increased wear and abrasion resistance
  • Added sling body (density)

If you choose to wax the entire sling it can be limited to step 1 below, giving the sling more body. Or you can give the entire cordage an outer layer of wax by following steps 1 and 2 below. Step 1 focuses on adding body to the sling while step 2 is more about outer abrasion. Keep in mind that step 2 will give the sling a slight tack feel.

However, it is essential to wax the last 2 inches of the release cord with both steps 1 and 2 and follow up with rubbing on additional wax before each slinging session.

Pan's Sling Wax can be used on other waxable fabrics as well. Follow manufacturer recommendations. You will skip step 2 in the waxing instructions when applying to other fabrics.

Cord Waxing Instructions

Step 1

To apply wax to your sling cordage, work in 6-12" manageable sections. Apply the wax in 3-6 smooth strokes along the cord, making sure to coat the entire circumference of the cord evenly. Then, use a hair dryer to melt the wax into the cord. Do not use a heat gun, it will melt and ruin the cord. Repeat this process 1-3 more times, until the wax no longer easily absorbs into the cord. This will add density to the cordage and create a foundation for the final coat of wax.

Step 2

To finish, apply a thin coat of wax to the surface of the cord by pulling it through your fingers. Avoid using direct heat for this final coat. The goal is to have a thin, protective layer of wax on the surface. You can always reheat the cord with a hairdryer and wipe off any excess wax if needed.

Before each slinging session, re-apply wax to the last few inches of the release cord, just before the leather release tab. This can be done easily in the field.

Follow-up waxing

To remove dirty wax or apply more wax to worn-off sections:

  1. Heat the wax with a hair dryer.
  2. Wipe off the wax with a paper towel.
  3. Reapply wax (if desired) following step 2 of the instructions above.

With a block of Pan's Performance Wax, you can quickly rub wax on worn-off areas, whether you are at home or in the field.

Removing wax

To remove wax, heat it with a hairdryer and wipe it down with a paper towel. Do not use a heat gun, it will melt and ruin the cord.

Note: Once you add wax to the sling, it will permanently darken the sling, even if you remove the wax from the surface of the cord. It is not possible to completely remove wax from the inner fibers of the cord.

Customer Reviews

Based on 3 reviews
100%
(3)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
b
b.r.

Simple, easy to apply when instructions are followed. As advertised.

J
James

Great wax, typical beeswax can be a little flakey. This stuff is the perfect equilibrium between pliability and cohesion.

C
Carl R.
Works well

Used it on my sling and it worked well. Sling is more dense now and cracks a little easier. I think it will help the sling last longer too. No problems with stickiness or flaking. You can tell it's made from good wax.